Modern Muzzleloader Forum

Modern Muzzle Loader ForumBlackhorn209 Shooters: General DiscussionInside joke

Please or Register to create posts and topics.

Inside joke

#1 · 06/30/2023, 10:52

I was takin a stroll thru here, then went into the ” other – MML ” and instantly it hit me when I saw one of this particular persons posts that ——–

There’s F-ing FINALLY, a ” Shooting/Muzzleloading ” forum that ENCORE50A – IS NOT IN!!! Who’da Thunkit… WOW!!! & YAYYYYYYY!!!

Yesssss, I know I’m bad…..but I’m funny too & sometimes I just can’t stop myself

timmoss.social, customguns and Sideshow have reacted to this post.

#2 · 07/07/2023, 15:05

you are naughty1

Ninering62 has reacted to this post.

Dan koich

#3 · 07/09/2023, 03:04

Ninering62 ya better look at that list again , i distinctly see a stain in the underwears backdoor . The keyboard clown has arrived . After what i read online thats pretty ballsy to show his face around here . However its typical . .

#4 · 07/16/2023, 10:36

What’s typical is you starting right off with insults & name calling like the fat bully kid on the elementary school playground, and speaking of keyboard clowns in poo stained undies….. you have some nerve. I see that you have not learned anything from all the other forums that you’ve been banned from or just shut down & run out of have you. So you want to bring that same obnoxious bad demeanor into this forum. I’m watching to see how long it takes for you to get the bums rush right out of here too.
Oh, and change your underwear & put some pants on.
Well I’d really like to say that it was lovely to catch up, but I just can’t.

#5 · 07/16/2023, 12:40

glad to see ya here Encore50A 🙂

i also got banned from MML ….. because i got tired of hal letting other folks make religious comments but wanting to delete mine and threatening me because he’s willfully ignorant on applying the rules fairly and consistently and i finally told him what i thought of him in a PM knowing i’d be banned .

anyhow , how is your knee coming along ?

take care , jeff

ENCORE50A has reacted to this post.

#6 · 07/16/2023, 13:22

Purpose of this forum is to have a place where info can be freely shared in a civil manner. If what you have to say would not be accepted in polite company, then perhaps it shouldn’t be said here. Encore50A and I have had our differences. He’s welcome here if he plays nice in our sandbox, but he better play nice. My offer still stands for him to stop by my place sometime. I would venture to guess we’d get along fine. It’s unfortunate how not speaking face to face emboldens bad behavior. We had a much more civil society when dueling was legal. Rude behavior had serious consequences at that time, so most people were polite.

Ninering62 and ENCORE50A have reacted to this post.

#7 · 07/16/2023, 21:09

Quote from Decay on 07/07/2023, 15:05

you are naughty1

LOL, only when I’m awake bro.

#8 · 07/22/2023, 08:01

Quote from JeffB1961 on 07/16/2023, 12:40

glad to see ya here Encore50A 🙂

i also got banned from MML ….. because i got tired of hal letting other folks make religious comments but wanting to delete mine and threatening me because he’s willfully ignorant on applying the rules fairly and consistently and i finally told him what i thought of him in a PM knowing i’d be banned .

anyhow , how is your knee coming along ?

take care , jeff

I heard that you were banned from MML & why. Hal is my friend and a good man, so I am not going to say any more about that. The knee, thanks for asking, is fine. It’s still connected to the thigh bone & the shin bone, so I’ll keep it. Have you joined any other forums since your departure from MML? I see some familiar names in here from MML & a couple not so popular names too.

#9 · 07/22/2023, 08:13

Quote from Ninering62 on 06/30/2023, 10:52

I was takin a stroll thru here, then went into the ” other – MML ” and instantly it hit me when I saw one of this particular persons posts that ——–

There’s F-ing FINALLY, a ” Shooting/Muzzleloading ” forum that ENCORE50A – IS NOT IN!!! Who’da Thunkit… WOW!!! & YAYYYYYYY!!!

Yesssss, I know I’m bad…..but I’m funny too & sometimes I just can’t stop myself

Lol well it looks like I have screwed that all up for you ninering. I see you and your buddy sideshow are in here slumming the place up already. Hopefully it won’t take very long for you both to get yourselves banned since neither of you have anything of real substance to contribute to anything anywhere unlike myself and about 2 or 3 others I see in here.

Ninering62 has reacted to this post.

#10 · 07/22/2023, 08:26

Yeah encore little big man ( the Other Sideshow ) ya sure did. Having to see you & sideshow in another forum flapping your gums like the resident experts in all things really is like getting a prostate exam from Edward Scissorhands. He’s no more my buddy than you are & I don’t relish hearing another damn thing from either of you in all honesty. In fact, I really think that you, sideshow & that psychotic Ahole idaholewis should have your own forum with no one else in it but you 3. You 3 truly deserve each others company. I can’t wait to see more of you & sideshow pullin each others hair & kickin each other in the shins over every single thing the other posts. I’m twisting one up & popping a beer in anticipation for that.

Comments

21 responses to “Modern Muzzleloader Forum”

mb.mnt.monkey@gmail.com

06/19/2023

Been shooting a converted pair amount for about a year now Woodman arms did it for me Mark at Woodman arms if anyone else is looking, I’m a big Paramount fan in spite of the issues a lot of people have had with bullets and board dimensions I had those problems with my gun and that’s why I chose to be Barrel it very happy with it and the results and 18 twist brux,, was I able to get a number 17 Contour down into the factory stock with a little work I have since then put a new stock on the rifle a lot more to say maybe it’s time goes on.

Log in to Reply
mb.mnt.monkey@gmail.com

06/19/2023

First post on a new site and I don’t bother to hit spell check sorry about that I do have my own language

Log in to Reply
timmoss.social

06/19/2023

See your post.

Log in to Reply
Sideshow

06/19/2023

Well thats a pretty hot load alright in a 40 !!! A bit hotter than i desire .

Log in to Reply
1. customguns
  
  06/19/2023
  
  It is, but I checked with Ken at Brux Barrel and Kyle Pittman ran the Quickloads calculation on it. It’s a right stout recoil, even with a muzzle brake, but manageable and safe in my rifle.
  
  Log in to Reply
  1. Sideshow
    
    06/19/2023
    
    Yes a QuickLoads program is a Requirement for the 40 if you intend to stay healthy lol . In fact its difficult to keep lighter bullet loads in the 49 to 53 Kpsi areas with some faster powders and light bullets . Thats what Hankins brass moduals will handle usually . The Alum-bronze ,AB ,hard moduals handle to 62k psi or so . The quick pressure rise of a 40 is both good and bad but definately one to watch out for Very Carefully . The higher pressure is needed for cleaner burning of a powder . Just watch out for the 40s tendacy to suddenly spike with very little more powder .
    
    Log in to Reply
Sideshow

06/19/2023

What i dont like is 300gr and above bullets seem to take massive powder charges to obturate bullets acceptably and truthfully full sizing too . TRUTHFULLY Direct ignition should be used too to help obturation with the long heavier bullets .
Life on the lighter side is just far easier to me all around .

Log in to Reply
Sideshow

06/20/2023

INCIDENTLY ADMINISTRATORS …….
Mtn Monkey gave me the web address of this site . On a google search it WONT BE FOUND . Without Marks info i Never could have got on here . Even to re find this site i must put that link he gave me back in . The history on my device connects to No Where . Just a heads up on what ive found guys . Figure i best say something .
Oh yes i was going to start a thread under the 700ml section and couldnt figure out how to post it ?? Lol i know that sounds bad but……
Thanks for your attention on these details . Sideshow…..

Log in to Reply
1. Sideshow
  
  06/20/2023
  
  My bad — I didnt tell you all congatulations !! Sorry guys .
  I know gettng the bugs out and such is only a time thing and will be handled . I hope to see you grow and prosper too . Smokeless muzzleloading seems to be in another “changeing” mode now . Im likeing the apparent offerings in choices listed . Good idea !!!
  
  Log in to Reply
2. customguns
  
  06/21/2023
  
  It will take awhile for the site to rank on a Google search, but it’s registered with the search engines. Just takes time.
  
  Log in to Reply
  1. Sideshow
    
    06/22/2023
    
    Ok . I know new usually does .
    
    Log in to Reply
  2. Sideshow
    
    06/26/2023
    
    I hate to say this but ive been continueing to use google search to find this site . It doesnt work .
    I believe you are going to need a name change to be found . The previous site with this name is the ONLY ONE OFFERED .
    This will kill this one before it ever has a chance . If i dont use the web address mtn monkey gave to to click on i dont get on here . If i put in the Same Exact Things that are in the web address he gave me IT WILL NOT CONNECT TO HERE !!!
    If i were you id change the name because here is Not Recognized AT ALL . JUST SAYIN……this isnt working out .
    
    Log in to Reply
    1. customguns
      
      06/27/2023
      
      Sideshow,
      Took four months for my website to show up on Google and I used a professional company to register with all the search engines. This site shows up first on Yandex and second on several others. Google is not gun friendly. Site has been up a week. To pronounce it’s not working out is premature. I currently have five websites. All of them took time to climb the search engine rankings. By time I mean months.
      
      Log in to Reply
      1. Sideshow
        
        06/29/2023
        
        Tim the operation of this site has more troubles than you think . Not being a Smart A** just being honest . I cant tell you how many times ive had to make a new passward because mine doesnt work day to day . Yes im frustrated but im.also here to help you . Im telling you theres problems with this site . Whorever put it up professionally has got bugs to chase out of it . It Doesnt Work Right .
logandriggers

06/30/2023

Never owned a smokeless muzzleloader but am an avid hunter. What would be a great first smokeless muzzleloader to get

Log in to Reply
1. customguns
  
  07/07/2023
  
  Convert a CVA Scout 45/70 to a smokeless .45. Inexpensive way to get into SML and it’s a very accurate gun.
  
  Log in to Reply
customguns

07/01/2023

As you find bugs please let us know so we can address them. Thanks

Log in to Reply
Decay

07/07/2023

Hi Tim.

I like the idea of having you convert my Paramount 45 cal to a 40 cal Brux barrel so I can use VVN120 and a Fury 225gr Black tip. I want a 400 yd capable rifle that shoots incredibly good, and doesn’t kick my shoulder to death. I don’t want to use a muzzle brake. This rifle is almost exclusively for deer hunting from tower tree stands in the cold of Wisconsin’s December muzzleloader hunt. I’d like to keep the Paramount stock, and have the barrel match the OEM barrel’s external dimensions as close as possible to minimize cost of stock alterations, but if alterations are necessary, then that’s ok too. The barrel should match the color of the Paramount/Bergara barrel, or maybe a matte silver, but not be a shiny, high gloss finish, I’ll keep my Leupold VariXIII, 6 x 20 x 42 on it.

What twist is best for the 225 grain, .402 Fury? 1:14? Do you think I’m wrong wanting the lighter weight Fury? If so what do you recommend?

I’ll need you to help me order the Brux barrel.

Thanks.

Log in to Reply
1. customguns
  
  07/07/2023
  
  I’ll defer to Mountain Monkey, Ninering62 or one of the other guys on best rate of twist on a light bullet. I only shoot heavier bullets, 350 grain in the .40. I like the high ballistic coefficient and energy dump the heavier bullets deliver. Where I hunt if the deer or bear doesn’t drop in its tracks, I may never find it. It’s always been my understanding the quicker rate of twist is for heavier bullets. My .40 has a 1 in 14 twist rate and I get .25” groups at 100 yards using 350 grain bullets.
  
  Log in to Reply
2. Sideshow
  
  07/09/2023
  
  That 1 in 14 will serve you just fine for a 40 useing light bullets . You also will be fine with a #6 Brux on the gun for shooting considerably heavier loads and bullets . I have that now and will be recontouring to a 1.2 inch shank for a half pound loss with a slightly heavier , .025″ , than a #5 barrel for more weight reduction . I wont venture over the 275gr pittman or hammers with up to 80 gr of H4895 . Thats mid 2900s + velocity . 8lbs scoped braked or not thats gonna kick . 56 to 57gr of 4198 w a 225gr is 2800 fps from a 26in barrel . Less n120 will put you there and easily kill deer to 400yds and more .
  Youll want pittman hardcores too so the 228s he calls them . 2550 fps and under for regular pittmans that open up quickly and do massive damage but use the 3gr heavier hardcores for velocitys above that . Especially if youd like a exit wound . Hope this helps ..
  
  Log in to Reply
Mach3 Muzzleloaders

07/07/2023

I use “Startpage.com” as my search engine when possible. It was developed by a conservative computer Geek. It does not track or keep records of your searches.

Log in to Reply